For ordering details and to check availability, please ring Stephen Harris on 01686 628446
All kits are to 2mm:foot scale and are to 2FS standards. The 12.25mm axle length applies to all 4 wheel wagon kits and bogies where applicable.
The etched components of all kits are 0.25mm thick nickel silver, and soldered construction is recommended.
Top hat bearings, wheels, buffers, couplings, vacuum cylinders are not included in the kits; these components should be obtained from the 2mm Scale Association shop.
Various nickel silver or brass wires are required to complete most kits - Eileen's Emporium.
Bogie wagons - bogies are not included with the kit unless noted otherwise.
4 wheel wagons - axleboxes and springs are included on the etch (in some
kits more than one type are provided) unless noted otherwise.
4 wheel wagons - (N) denotes that N gauge wheels (2mm shop reference 2-027)
can be used with this kit.
Please ring to check availability of kits before ordering.
For most kits which consist of an etch only, a 'sheet rate' discount is
available for quantity orders, however these will be subject to extended
delivery times (probably months). Please ring for details.
Postage is additional to the cost of the kits. For UK addresses the cost is typically £2.00 (for etched kits only) or £3.50 (if the order includes resin cast bodies) for any number of kits.
Cheques payable to S Harris.
For additional information please contact me on 01686 628446 (evenings after
8pm please).
This list of kits is dated July 2015.
| Wagon type | Diagram No. | TOPS code | £ Cost per kit | Notes |
|
Catfish |
1/586 |
ZEV |
6.50 |
Axleboxes and springs not included. (N) |
 |
||||
|
Dogfish |
1/587, 1/588 |
ZFV |
8.25 |
Axleboxes and springs not included. Includes optional hopper extensions for slag ballast version diagram 1/588. (N) |
 |
||||
|
Unfitted plate |
1/430, 1/431 |
SPO |
6.50 |
Axleboxes and springs not included. LMS W-irons and BR plate irons included. (N) |
 |
||||
|
13T All Steel High |
1/031, 1/037, 1/041, 1/046, 1/047, 1/049 |
OHV |
8.25 |
Axleboxes and springs not included. Includes Shochigh version. (N) |
 |
||||
|
16T mineral |
1/108 |
MCV,MCO, MXV |
6.50 |
Original body with top flap. 4 brake variations included. (N) |
  |
||||
|
16T mineral |
1/108 |
MCV,MCO, MXV |
6.50 |
Rebodied version, no top flap. 4 brake variations included. (N) |
 |
||||
|
21T mineral vacuum fitted |
1/119, 1/120 |
MDV |
6.50 |
(N) |
 |
||||
|
21T mineral unfitted |
1/107 |
MDO |
6.50 |
Original body. (N) |
 |
||||
|
21T mineral unfitted |
MDO |
6.50 |
First rebuild early 1970’s, mainly Swansea area. (N) |
|
 |
||||
|
21T mineral unfitted |
MDO |
6.50 |
Second rebuild mid 1970’s, one side door only per side, no end doors. (N) |
|
 |
||||
|
24½T mineral unfitted |
1/115, 1/118 |
MEO |
6.50 |
(N) |
 |
||||
|
21T hopper |
1/149 |
HTO, HTV |
7.75 |
Original body with 5 side ribs, 3 angle struts to support hopper ends. |
 |
||||
|
21T hopper |
1/147 |
HTO, HTV |
7.75 |
Rebuilt body with 2 side ribs. No instructions, but instructions for original body version covers most of the assembly process. |
 |
||||
|
20T coke |
1/151 |
HCO |
6.50 |
Solid ends, raved sides. Outline instructions only. (N) |
 |
||||
|
20T coke |
1/152 |
HCO |
6.50 |
Solid ends, solid sides. Outline instructions only. (N) |
 |
||||
|
Coil J |
KJO |
7.75 |
Cradle not included. (N) |
|
 |
||||
|
Iron ore tippler |
1/180, 1/181 |
MSO |
7.75 |
Original 9’ WB version with bodywork height matching 1/108 mineral wagons. (N) |
 |
||||
|
Iron ore tippler 9’ WB |
1/183 |
MSO, MSV |
6.50 |
Later version with lower bodywork height than 1/108 mineral wagons. (N) |
 |
||||
|
Iron ore tippler 10’ WB |
1/184, 1/185 |
MSO, MSV |
8.00 |
As 9’ version above but with 10’ WB conversion chassis, choice of unfitted push brakes and vacuum fitted clasp brakes. (N) |
 |
||||
|
BR Bogie Bolster C, GWR Macaw B |
1/471, 1/473, 1/475, 1/477 |
BCO, BCV |
10.50 |
Macaw B can be built with either angle trussing or truss rodding (wire for latter not included in kit). |
 |
||||
|
Bogie Bolster E |
1/479 |
BEV |
6.50 |
|
 |
||||
|
Bogie Bolster D |
1/472, 1/476, 1/478, 1/484 |
BDO,BDV |
7.75 |
|
|
|
||||
|
Bogie Bolster A |
BAA |
10.50 |
Air-braked high capacity vehicle, 1970’s. Coil cradles included. 4-post and 5-post ends included. |
|
 |
||||
|
Bogie Bolster B |
BBA |
10.50 |
Air-braked high capacity vehicle, 1970’s. |
|
 |
||||
|
Boplate E |
1/490, 1/491, 1/492 |
BPO/BPV |
N/A |
Future release, not yet available. |
 |
||||
|
35T tank |
TSV |
11.75 |
Resin cast tank, choice of class A tank or class B. Etched chassis. (N) |
|
 |
||||
|
45T monobloc tank |
TTV, TTA |
12.50 per wagon but sold in pairs |
Resin cast tank including solebars and bufferbeams. Etched chassis and choice of catwalks/ladders. (N) |
|
|
|
||||
|
Grampus |
1/572, 1/574 |
ZBO, ZBV |
7.75 |
Can be built with unfitted push brakes or vacuum fitted clasp brakes. (N) |
 |
||||
|
Cartic 4 |
PJA |
50.00 per set of 4 units |
Set comprising 2 outer and 2 inner units as originally built (i.e. no mesh screens). Outline instructions only. Etched bogie frames are included but the bogie sideframe castings are not. |
|
 |
||||
|
Freightliner flats |
1/082, 1/083, 1/084, 1/086 |
FFA, FGA |
36.00 per set of 5 flats |
Set comprising 2 outer and 3 inner flats. |
 |
||||
|
Sturgeon |
1/645, 1/647 |
YBA, YBO |
15.00 |
Bogies are included on the etch. |
 |
||||
|
Carflat from mark 1 coach chassis |
1/131 |
FVV |
7.75 |
‘Motorail’ flat. |
 |
||||
|
25½T Ironstone hopper |
1/163, 1/166 |
HIO, HIV |
7.75 |
Can be built with unfitted push brakes or vacuum fitted clasp brakes. (N) |
|
|
||||
|
Sealion/Seacow |
1/590, 1/591 |
YGB, YGH |
7.75 |
Outline instructions only. As originally built (i.e. no mesh screen over end platforms). |
 |
||||
|
LMS CCT |
D2026 |
12.00 |
Includes both BR plywood and LMS planked end doors. Axleboxes and springs not included. |
|
 |
||||
|
Mermaid |
1/573, 1/575 and GWR unfitted |
ZJV |
see 2mm Shop |
Resin cast body, etched chassis. (N). This kit will soon be available in the 2mm shop, product code 2-700. |
 |
||||
|
Covhop |
1/210 |
CHO |
9.25 |
Resin cast body, etched chassis. (N) |
 |
||||
|
Salmon |
1/628, 1/637, 1/646 |
YMA, YMO |
7.75 |
8’ WB bogies are included. Outline instructions only. Requires various brass strips/sections from Eileen’s Emporium to complete (these are listed in the instructions). |
 |
||||
|
Vanwide |
1/217 |
VEV, VWV |
10.50 |
Resin cast body, etched chassis. (N) |
 |
||||
|
Standard brake van |
1/504, 1/506, 1/507 |
CAO, CAP, |
N/A |
(N). Future release, not yet available. |
 |
||||
|
Shochood B |
1/058 |
OUV |
N/A |
(N). Future release, not yet available. |
 |
||||
|
Wooden sided high |
1/039, 1/044 |
OHV |
N/A |
Wooden sides, corrugated steel ends, including optional ‘Highbar’ tarpaulin bar and fittings.(N). Future release, not yet available. |
|
GWR 6 wheeled milk tank |
GWR O.56 and others |
CMV |
N/A |
Etched chassis, cast resin tank. (N). Future release, not yet available. |
